高温空气下C/SiC复合材料力学性能测试

测试了C/SiC复合材料在高温空气下的压缩、弯曲和拉伸性能,利用扫描电子显微镜分析复合材料在室温与高温条件下的断口微观形貌。结果表明:从室温升温到1 000 ℃测试温度时,C/SiC复合材料的压缩强度由247 MPa降低至78 MPa,性能降低68%;弯曲强度由480 MPa降低至277 MPa,性能降低42%;拉伸强度由247 MPa降低至152 MPa,性能降低38%。高温氧化导致界面退化,损伤材料基体与碳纤维结构,加剧了纤维断裂程度,改变了纤维与基体的结合状态,纤维增韧机制逐渐消失,导致复合材料性能下降。     

Micromechanical simulation and experimental investigation of aluminum-based nanocomposites

Ceramic reinforced metal matrix nanocomposites are widely used in aerospace and auto industries due to their enhanced mechanical and physical properties. In this research, we investigate the mechanical properties of aluminum/Nano-silica composites through experiments and simulations. Aluminum/Nano-silica composite samples with different weight percentages of silica nanoparticles are prepared via powder metallurgy. In this method, Nano-silica and aluminum powders are mixed and compressed in a mold, followed by sintering at high temperatures. Uniaxial tensile testing of the nanocomposite samples shows that adding one percent of Nano-silica causes a considerable increase in mechanical properties of nanocomposite compared to pure aluminum. A computational micromechanical model, based on a representative volume element of aluminum/silica nanocomposite, is developed in a commercial finite element software. The model employs an elastoplastic material model along with a ductile damage model for aluminum matrix and linear elastic model for nano-silica particles. Via careful determination of model parameters from the experimental results of pure aluminum samples prepared by powder metallurgy, the proposed computational model has shown satisfactory agreement with experiments. The validated computational model can be used to perform a parametric study to optimize the micro-structure of nanocomposite for enhanced mechanical properties.     

3维C/SiC-ZrC复合材料的制备及其性能研究

针对超高温环境应用需求,采用化学气相渗透工艺(CVI)与先驱体浸渍-裂解工艺(PIP)联用制备了3维碳纤维增强SiC-ZrC基复合材料(C/SiC-zrC),并研究了SiC含量对C/SiC-ZrC复合材料力学性能、抗氧化性能和抗烧蚀性能的影响.结果表明,随着SiC含量的增加,C/SiC-ZrC复合材料的强度逐渐降低,静...     

侧面封边对玻璃纤维增强环氧树脂基复合材料吸湿规律的影响

采用称量法和排水法联合,研究了侧面封边和未封边单向玻璃纤维增强环氧树脂基复合材料层合板试件的吸湿量和体积变化率与浸泡时间的关系,结果显示,复合材料侧面吸湿的速度远大于表面吸湿速度;侧面封边复合材料试件的饱和吸湿量为1.30％,而未封边试件的为2.26％,即与侧面封边试件相比,未封边试件的饱和吸湿量(质量比)增加了73....     

三维石英纤维增强氮化物基复合材料的烧蚀性能及显微结构

采用先驱体转化法制备了三维石英纤维增强氮化物基复合材料(3D SiO2f/Si3N4-BN),用等离子射流烧蚀方法研究了复合材料的烧蚀性能,运用扫描电镜及能谱仪对烧蚀表面微观形貌进行了观察和分析。结果表明氮化物基复合材料在高压高热流等离子体烧蚀下线烧蚀率为0.91mm/s,石英纤维熔融并被吹除带走了大量的热量,熔融层抑制了基体的机械剥蚀。基体由于强度高、升华温度高,延缓了熔融层的吹除,表明氮化物基复合材料是一种良好的耐高温烧蚀透波材料。     

纳米材料和纳米技术提升传统产业

纳米材料具有一些特殊的、优异的性能,将纳米材料作为复合添加剂对某些传统产品进行改性,可以显著提高产品的性能或使他们具有新的功能。研究了不同的纳米复合材料在聚胺酯合成革、外墙涂料、塑料、抗菌剂、永磁铁氧体以及润滑油等方面的改性和工程应用,并简述了利用纳米技术在改造和提升传统产业方面取得的成果以及在产业化方面做出的实质性业绩。     

氮化硼先驱体的合成及其热分解特性

以硼氢化锂和硫酸铵为原料合成了氮化硼陶瓷先驱体环硼氮烷,以GC MS、FT IR和1H NMR等方法对其组成和结构进行了表征和确认.环硼氮烷在80℃左右保温72h后可以得到固化的聚硼氮烷,而后经热分解得到氮化硼陶瓷,以TG、FT IR、XRD等对聚硼氮烷的热分解行为进行了分析和表征.结果表明聚硼氮烷中仍然存在一定数量的B H和N H键,在后续的热分解过程中,会进一步发生脱氢反应,1400℃时陶瓷产率约为89.5%.B H键的断裂主要发生在800℃以前,N H键的消失则需要较高的温度.聚硼氮烷800℃热分解后无机化程度已经较高,其产物基本上为无定形的BN,在1600℃则形成h BN.     

纳米SiC晶须增强铜基纳米复合材料摩擦学性能研究

采用粉末冶金法制备了添加纳米SiC晶须（n-SiCw）的铜基纳米复合材料（SiCw／Cu）。研究了复合材料的显微组织、密度、硬度与n-SiCw含量之间的关系，通过球／盘式摩擦磨损试验机研究了SiCw／Cu复合材料的摩擦磨损性能。结果表明：随n-SiCw含量增加，基体中孔隙增多，并出现n-SiCw的偏聚，复合材料的密度减小，硬度增加；当n-SiCw含量为0．3wt％时，材料的减摩、耐磨性能最好；SiCw／Cu复合材料的磨损机制为疲劳磨损和磨粒磨损，并以疲劳磨损为主。     

An investigation on anti-impact and penetration performance of basalt fiber composites with different weave and lay-up modes

The woven basalt fiber composites (WBFC) and the unidirectional [0°/90°/45°/-45°]_s basalt fiber composites (UBFC) were prepared by hot-pressing. Three-point bending test, low velocity impact test, and ballistic test were performed to the prepared composites. After the tests, the specimens were recovered and analyzed for micromorphology. Three-point bending tests show that both the bending strength and stiffness of the WBFC surpass those of the UBFC. Low velocity impact test results show that the low velocity impact resistance to hemispherical impactor of the UBFC is higher than that of the WBFC, but the low velocity impact resistance to sharp impactor of the UBFC is lower than that of the WBFC. For the ballistic test, it can be found that the ballistic property of the UBFC is higher than that of the WBFC. After the tests, microscopic analysis of the specimens was applied, and their failure mechanism was discussed. The main failure modes of the UBFC are delamination and fibers breakage under the above loading conditions while the main failure mode of the WBFC is fibers breakage. Although delamination damage can be found in the WBFC under the above loading conditions, the degree of delamination is far less than that of the UBFC.     

添加SiC微粉对硅树脂先驱体转化3D Cf/Si-O-C材料性能的影响

以三维碳纤维织物和廉价的硅树脂为原料,采用先驱体转化工艺制备3D G/Si-O-C材料,考察了浸渍液中添加SiC填料对材料微观结构、力学性能和抗氧化性能影响.结果表明:添加适量的SiC填料有助于减少基体孔隙,改善界面结合,从而提高材料的力学性能;而SiC含量过高时,容易在材料内部形成闭孔,从而导致材料力学性能下降.当SiC微粉含量为18.2%时,材料具有最好的力学性能,弯曲强度和断裂韧度分别为421.3MPa和13.0 MPa·m1/2;而材料的抗氧化性能随着SiC微粉含量的增加而增加,当SiC微粉含量为25.0%时,材料的弯曲强度保留率最高,达到了89.5%.